Quuppa for Mobile Duress: What a Real Security Escort Replacement Looks Like

Quick answer: Quuppa is a real-time locating system that uses Bluetooth Low Energy Angle of Arrival (AoA). Ceiling-mounted Quuppa Locators measure the direction a badge's signal comes from, so the position is calculated from angles rather than guessed from signal strength. That typically gets an alarm to within about a metre, which means the right room, the right cell and the right floor. Quuppa runs on its own dedicated network, not the hospital or prison Wi-Fi, needs no site-wide calibration walk, and can be installed alongside Security Escort so there is never a shift without duress cover. It is live today at Thomas Embling Hospital in Melbourne and at Gawler and Port Pirie hospitals in South Australia.
Prefer to listen? This article accompanies Episode 3: What a Real Replacement Looks Like of Mark's podcast series on replacing Bosch Security Escort.
Key facts
Technology: Bluetooth Low Energy Angle of Arrival (BLE AoA).
Typical accuracy: around one metre (sub-metre in good geometry).
Network: standalone. Badges talk to Locators over Bluetooth; Locators are cabled back to the Quuppa positioning engine. No dependency on Wi-Fi.
Calibration: no site-wide fingerprinting walk. Position comes from geometry.
Live in Australia: Thomas Embling Hospital (Forensicare, Victoria), Gawler Hospital and Port Pirie Hospital (South Australia).
Why the old way falls short
Legacy duress systems, Security Escort included, listen for how loud a signal is at each receiver and make an educated guess about where it came from. Signal strength bounces off concrete and steel, so the guess drifts. That is why five metres was once considered good.
Quuppa works differently. Each Locator in the ceiling measures the angle the signal arrives from. When several Locators hear the same badge, the position is where those angles meet. Less guessing, more geometry.
What that means on the floor
The alarm shows up in the right room, the right cell, the right side of the wall, on the right floor.
The control room sees a name and a room, not a dot in a general area.
If the person is moving, the system keeps tracking them until the alarm is reset, so responders follow the person, not the place the alarm started.
For corrections teams who tell me they need "which cell, not roughly where", this is the difference.
"Does it run on our Wi-Fi?"
This is the first question every IT team asks, and the answer is no, by design.
Quuppa is a standalone network. Badges talk to Locators over Bluetooth, and Locators are cabled back to the positioning engine. Hospital and prison networks go down, get upgraded and get reconfigured. A duress system should keep working regardless. Independence from Wi-Fi is a resilience feature, not an omission.
Lighter install than most people expect
In a prison, lifting a ceiling tile is a security event, so installation matters.
Several Locators can run from one network port, which keeps cabling light.
We can often reuse existing Bosch cable paths and mounting points.
There is no site-wide calibration walk, because positioning comes from geometry rather than fingerprinting.
It has to do everything Security Escort did
A replacement is not a replacement unless it integrates with the rest of the site. As a minimum that means the security management system, automatic camera call-up, paging, and a full audit trail. That is the floor, not a feature list.
Changing over without a gap in cover
The question every site asks: how do we switch without leaving staff exposed?
Run both systems side by side.
Quuppa is installed while Security Escort keeps running.
Each area is tested with real people pressing real buttons in real rooms.
Once an area is proven, it cuts over.
Only then does the old equipment come out.
No shift goes without duress cover. Not one.
Where it is running today
Thomas Embling Hospital, Melbourne. A secure forensic mental health facility operated by Forensicare, and the closest environment to a prison I can point you to.
Gawler Hospital and Port Pirie Hospital, South Australia. Both live on Quuppa after we removed a drop-in system that did not meet our standard (see Part 2).
Frequently asked questions
What is Quuppa? Quuppa is a real-time locating system (RTLS) that uses Bluetooth Low Energy Angle of Arrival to locate tags and badges, typically to within about a metre.
How accurate is a Quuppa duress system? Typically around one metre, which is accurate enough to identify the specific room or cell an alarm was raised in.
Does Quuppa use Wi-Fi? No. Quuppa is a standalone network: badges communicate with Locators over Bluetooth, and Locators are cabled to the positioning engine. It does not depend on the site's Wi-Fi.
Does Quuppa need calibration? It does not need a site-wide fingerprinting or calibration walk. Position is calculated from the geometry of the Locators.
Can Quuppa reuse Bosch Security Escort cabling? Often, yes. Existing cable paths and mounting points can frequently be reused, and several Locators can share a single network port.
How do you replace Security Escort without losing cover? Install Quuppa alongside Security Escort, test and cut over one area at a time, and remove the old equipment only once each area is proven.
Next in the series
Part 4: The badge staff actually wear. Why the Infrafon CC2 duress badge was designed for mental health and corrections.
The full series
Part 1 of 5: Bosch Security Escort End of Support: What 31 December 2026 Means
Part 2 of 5: Bosch Security Escort Replacement: Why Keeping the Old Hardware Is a Band-Aid
Part 3 of 5: Quuppa for Mobile Duress: What a Real Security Escort Replacement Looks Like (you are here)
Part 4 of 5: Infrafon CC2: The Duress Badge Built for Mental Health and Corrections
Part 5 of 5: WillowCreek, Quuppa and Infrafon: One Duress Platform, and a Standard to Test It
Related reading
Mark Winter leads inTechnology Distribution, a Quuppa partner, and has worked in mobile duress for more than 25 years. Planning a Security Escort replacement? Get in touch at intechnology.com.




Comments